Picture #1
We Call This the BEFORE Picture.
|
Picture #2
Blitz Controller Will be Molded Into an Air Vent Location.
|
Picture #3
Two Pieces Fused Together.
|
Picture #4
Modified Dash Piece With Tein Controller & iPod Setup.
|
Picture #5
Blitz piece Painted, and Mounted in Dash.
|
Picture #6
Two NX Nitrous Tanks Mounted in Trunk.
|
Picture #7
We Call This the AFTER Picture.
|
Picture #8
Clean Shot of the Center Console Setup.
|
Picture #1
Rear Bumper Removed for Hidden Radar Sensor Installation.
|
Picture #2
Bumper Clearanced for Sensor.
|
Picture #3
Styrofoam Insert Back in Place Over Bumper Support.
|
Picture #4
Front Sensor Hidden in Nose of Car.
|
Picture #5
Shot of Rear Seat and Floor of Car Dynamatted.
|
Picture #6
Front Floor Dynamatted as Well.
|
Picture #7
Driver's Side Shot. Amp Pre-Wiring for Under Seat Mounting.
|
Picture #8
Subwoofer Cabinet Built & Dynamatted Into Rear Seat. Sealed Baffle Style.
|
Picture #9
Cabinet Has a Routered Recessed Face and Good Bracing Between Subs.
|
Picture #10
Cabinet Wrapped in Matching Trunk Liner. Wired, and Ready for Woofers.
|
Picture #11
JL 10W3 Subs Mounted Into Sub Cabinet.
|
Picture #12
Rear Seat Bolted Back in Place.
|
Picture #13
Seat Folded Down. The Sub Cabinet Looks Perfectly Integrated.
|
Picture #14
Instrument Cluster Showing Hidden LED's for Radar Detector.
|
Picture #15
Back Side of Sub Cabinet.
|
Picture #16
Tons of Trunk Room Left.
|
Picture #17
Front & Rear Radar LED's Lit Up in Turn Signal Locations.
|
Picture #1
Passenger Door Sound Deadened, Ready for Speaker Upgrade.
|
Picture #2
Stock Mid Compared to Hertz Space 8" Mid.
|
Picture #3
Close-up of Hertz 8" Mid. Note the Magnet in the Front of the Speaker.
|
Picture #4
8" MDF Ring for Solid Mounting of Mid. Makes Mid Sound Solid & Snappy.
|
Picture #5
Ring Sealed Into Door With Scosche Accumat.
|
Picture #6
8" Mid Mounted and Wired Up.
|
Picture #7
Driver's Side Door With Mid Mounted.
|
Picture #8
Factory Speaker Grill Comes Partially Blocked. No Good for Sound.
|
Picture #9
Grills Wrapped With Grill Cloth.
|
Picture #10
Speaker Grill After Modification. Each Hole Was Individually Drilled out.
|
Picture #11
Factory Tweeter Panels.
|
Picture #12
Original Small Factory Tweets.
|
Picture #13
Tweet Panels Sanded in Prep for Modification.
|
Picture #14
Tweet Cups Prepped.
|
Picture #15
Cups Bonded to Panels, Prepped for Body Filler.
|
Picture #16
Pod Starting to Take Shape.
|
Picture #17
Body Filler Sanded Smooth.
|
Picture #18
Hertz Tweeter Test Fitted Into Pod.
|
Picture #19
Hertz Tweeter Test Fitted Into Pod.
|
Picture #20
Pod Textured and Painted.
|
Picture #21
Pod Textured and Painted.
|
Picture #22
Car Gutted Before Accumat.
|
Picture #23
Rear Speaker Location and Behind Seat Compartments
|
Picture #24
Crossovers Tucked Behind Passenger Seat Area.
|
Picture #25
1ga Power and Ground Going Out to Amplifiers.
|
Picture #26
Small Rack to Hold Crossovers Out of the Way.
|
Picture #27
Rack to Hold 2nd Battery, Capacitors, & Fuse Distribution.
|
Picture #28
Hertz High Energy 6.5" Coaxial Speakers for Rear Fill
|
Picture #29
Driver's Side Floor Completely Accumatted.
|
Picture #30
Headliner Sound Deadened as Well.
|
Picture #31
Hatch Area Covered in Accumat.
|
Picture #32
Exterior Shot While Running Wiring.
|
Picture #33
Grillcraft Grill in Front.
|
Picture #34
Hatch of 350z Accumatted. 1ga Cables, RCA, & Speaker Wiring Run.
|
Picture #35
Space Tweeter Pods Mounted in Car.
|
Picture #36
Tweeters Angled for Optimal Imaging.
|
Picture #37
Driver's Tweeter Looks as Good as it Sounds.
|
About Us
Acura
Nissan
Previous Page
Frontier Parrot
